Installing IFace inside the TS-2000 – 23 cm band

In a previous article we presented how to install the IFace card inside the Kenwood TS-2000 in order to obtain the IF signal of all bands so that it can be sent to an external SDR. Now let’s see how to get the IF signal for the 23 cm band. Installation is very easy.

The TS-2000, like other radios, has a fairly complex configuration and uses different intermediate frequencies depending on the band on which you are operating. In any case, the one described here is the sequence of operations to be performed to obtain a bandwidth sufficient to provide a panoramic receiver around the IF frequency relative to the 23 cm band (1.2 GHz).

The point where to take the IF signal can be identified more precisely through the wiring diagram as shown in the following images. The electronic board of interest is the one called TX-RX3 and the signal can be taken from the CN8 connector.

The point where to take the IF signal on the TX-RX3 UNIT is indicated in the following image.

For the sake of completeness, a detail of the point where to take the power supply for the IFace card is also indicated.

PTT: This is not required for the TS-2000 as the reception circuit is muted during transmission.

You can purchase IFace 2 using one of the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the IC-706MKIIG

These are the instructions to install the IFace interface inside of the Icom IC-706MKIIG. The installation is very easy.

The IC-706MKIIG, like other radios, has a fairly complex configuration and uses two different intermediate frequencies. We are interested in the first, the “wideband” one, the one before the main bandpass filter (the roofing filter so to speak). The sequence of operations to be performed in order to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency is shown below. The intermediate frequency filter is also used in transmission, so it will be preferable to use the PTT command to disable the IFace during transmission. The following images show the point where the IF signal will be taken.

Let’s start by analyzing the wiring diagram. We have to find the first mixer, the PTT and where to take the power supply. From the following images everything will appear clear.

PTT and power supply can be easily taken from the connector J10. The interesting signal are labeled as T8 and 13.8 respectively.

At this point we have to locate the points where we connect the electric cables to the IFace. The following images show where to take the various signals.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

Panadapter SDR for the TS-440s

To install the IFace card inside the Kenwood TS-440s follow the steps below.

The TS-440s, like other radios, has a fairly complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main bandpass filter. The sequence of operations to be performed to obtain a bandwidth sufficient to realize a panoramic receiver around the chosen IF frequency (45.05 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission may not be necessary, but if you use it the SDR receiver will be more isolated when transmitting. The following images show the point where the IF signal will be taken and the power supply.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

You can buy an IFace using the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

Panadapter SDR for the TS-430s

To install the IFace card inside the Kenwood TS-430s follow the steps below.

The TS-430s, like other radios, has a fairly complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main bandpass filter. The sequence of operations to be performed to obtain a bandwidth sufficient to realize a panoramic receiver around the chosen IF frequency (48.055 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission may not be necessary. The following images show the point where the IF signal will be taken and the power supply.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

Panadapter SDR for the IC-735

To install the IFace card inside the ICOM IC-735 follow the steps below.

The IC-735, like other radios, has a fairly complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a bandwidth sufficient to realize a panoramic receiver around the chosen IF frequency (70.451 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission may not be necessary. The following images show the point where the IF signal will be taken and the power supply.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the MAIN UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

Installing IFace inside the TS-2000 – VHF and UHF bands

In a previous article we presented how to install the IFace card inside the Kenwood TS-2000 to obtain the IF signal of the HF and 50 MHz bands in order to send it to an external SDR. Now let’s see how to get the IF signal for the VHF and UHF bands. Installation is very easy.

The result you can obtain is well shown in the following video.

The TS-2000, like other radios, has a fairly complex configuration and uses different intermediate frequencies depending on the band on which you are operating. In any case, the one described here is the sequence of operations to be performed to obtain a bandwidth sufficient to provide a panoramic receiver around the IF frequency relative to the VHF and UHF bands.

The point where the IF signal is taken can be identified more precisely using the electrical scheme as shown in the following images. The electronic card of interest is the one named TX-RX2 and the signal can be taken R167 or C233.

Now we need to find out where to get the power supply: energy can be taken from the CN 12 connector or from the CN 17, 14S signal.

  • PTT: for the TS-2000 it is not required because the reception circuit is automatically muted during transmission.

In the images that follow you can see the points where to take the IF signal: therefore the installation is really simple. Pay attention, for this RTX the IF sampling point is on the bottom layer of the TX-RX 2 UNIT.

You can by IFace 2 simply making click on the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the FT-1000MP Mark-V Field

These are the instructions to install the IFace interface inside of the YAESU FT-1000MP Mark-V Field. The installation is very easy.

The FT-1000MP Mark-V Field, like other radios, has a very complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (70.455 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the FT-1000MP Mark-V

These are the instructions to install the IFace interface inside of the YAESU FT-1000MP Mark-V. The installation is very easy.

The FT-1000MP Mark-V , like other radios, has a very complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (70.455 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the IC-7100

These are the instructions to install the IFace interface inside of the Icom IC-7100. The installation is very easy.

The IC-7100, like other radios, has a very complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (124.487 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the MAIN UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the TS-570D and the TS-570DG

These are the instructions to install the IFace interface inside of the Kenwood TS-570D/G. The installation is very easy.

The TS-570D / G, like other radios, has a complex configuration and uses several intermediate frequencies. We are interested in having a “broadband” signal, so it will be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to create a panoramic receiver around the chosen IF frequency (73.05 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT + signal to disable IFace during transmission is not strictly necessary but can help isolate the receiver during transmission. The following images show the point where to take the signals and the power supply.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the TX-RX UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the buttons below.

Paypal

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

© TSP S.r.l. | VAT IT03137540542 | V.le Unità d'Italia 36, 06019 Umbertide, ITALY

NEWS July 18, 2024
A Telegram group is now available through which you can interact to get faster responses from other customers or, if necessary, from TSP Srl. Sign up for free by clicking here: Telegram TSP Customers. Please limit the use of contact forms to send generic requests, they have low reading priority because they are often used to send spam.

NOVITA' 18 Luglio 2024
E' da oggi disponibile un gruppo Telegram tramite il quale interagire per avere risposte più veloci da altri clienti o, in caso, da TSP Srl. Iscrivetevi gratuitamente facendo click qui: Telegram Clienti TSP. Per favore limitare l'utilizzo dei form di contatto per inviare richieste generiche, hanno bassa priorità di lettura perché spesso usati per inviare spam.
This is default text for notification bar