fbpx

SDR interface for the FT-1000MP Mark-V Field

These are the instructions to install the IFace interface inside of the YAESU FT-1000MP Mark-V Field. The installation is very easy.

The FT-1000MP Mark-V Field, like other radios, has a very complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (70.455 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the FT-1000MP Mark-V

These are the instructions to install the IFace interface inside of the YAESU FT-1000MP Mark-V. The installation is very easy.

The FT-1000MP Mark-V , like other radios, has a very complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (70.455 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the IC-7100

These are the instructions to install the IFace interface inside of the Icom IC-7100. The installation is very easy.

The IC-7100, like other radios, has a very complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (124.487 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the MAIN UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the TS-570D and the TS-570DG

These are the instructions to install the IFace interface inside of the Kenwood TS-570D/G. The installation is very easy.

The TS-570D/G, like other radios, has a complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency (73.05 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission will not be necessary. The following images show the point where the IF signal will be taken.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the TX-RX UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the buttons below.

Paypal

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the IC-7600

These are the instructions to install the IFace interface inside of the Icom IC-7600. The installation is very easy.

The IC-7600, as well as other radios, has a fairly complex configuration and uses two different intermediate frequencies. We are interested in the first, the “wide band” one, the first one of the main band pass filter (the roofing filter so to speak). Below is the sequence of operations to be performed in order to obtain a sufficient bandwidth to make a panoramic receiver around the chosen IF frequency. Going over you can find some images that illustrate how to install the interface for SDR. The following image shows the point where the IF signal will be taken.

Let’s start by analyzing the wiring diagram. We have to find the first mixer, the PTT and where to take the power supply. From the following images everything will appear clear.

At this point we have to locate the points where we connect the electric cables to the IFace. The following images show where to take the various signals.

This last image shows the inside of the RTX and where the IFace interface is to be placed.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

SDR interface for the FT-897

Follow the steps below to install the IFace card in the YAESU FT-897. Installation is really very easy.

As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal. We use the first because it is not filtered, i.e. the band is still wide. The following images make it very clear where this point is located. The PTT may not be necessary, the TX and RX circuits are well separated.

The power supply can be taken soldering a thin wire on the fuse F1001.

At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.

If you are convinced of the goodness of the proposal buy an IFace using the button below.

WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.

For more information do not exist to write to us.
Have fun!

SDR interface for the FT-817

Follow the steps below to install the IFace card in the YAESU FT-817. Installation is really very easy.

IFace 2

As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal. We use the first because it is not filtered, i.e. the band is still wide. The following images make it very clear where this point is located. The PTT may not be necessary, the TX and RX circuits are well separated.

The power supply can be taken from the test point TP1084.

At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.

If you are convinced of the goodness of the proposal buy an IFace using the button below.

Paypal

Testimonial IFace installation on the FT-818: click here!

WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.

For more information do not exist to write to us.
Have fun!

SDR interface for FTDX1200

Follow the steps below to install the IFace card in the YAESU FTDX-1200. Installation is really very easy.

As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal. We use the first because it is not filtered, i.e. the band is still wide. The following images make it very clear where this point is located. The PTT may not be necessary, the TX and RX circuits are well separated. The power supply can be taken from a point very close to the relais labeled RL1007.

At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.

With the video below you can also view the instructions and listen to the explanations on how to install the IFace

In order to buy an IFace, please use the buttons below.

WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.

For more information do not exist to write to us.
Have fun!

SDR interface for the FT-991

Follow the steps below to install the IFace card in the YAESU FT-991. Installation is really very easy.

As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal. We use the first because it is not filtered, i.e. the band is still wide. The following images make it very clear where this point is located. The PTT may not be necessary, the TX and RX circuits are well separated. The power supply can be taken from the TP1034 near the J1018 connector.

At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.

If you are convinced of the goodness of the proposal buy an IFace using the button below.

WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.

For more information do not exist to write to us.
Have fun!

SDR interface for the IC-R72

Follow the steps below to install the IFace card in the ICOM IC-R72. Installation is really very easy.

As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal: we take the first because it is not filtered and the band is still wide. The following images make it very clear where this point is located (on resistance R82). Being a receiver, there is no need to look for the PTT signal. The power supply can be taken between the inductance L66 and the resistance R68.

At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.

Finally, this photo suggests where to place the IFace card and where to get the signals.

If you are convinced of the goodness of the proposal buy an IFace using the button below.

WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.

For more information do not exist to write to us.
Have fun!